Hood Latch

Home

 

Click Here To Visit
Click Here To Visit

Home
Up
RockBiters
Sound
On Board Air
PW Fenders
PW Fenders
DIY 2"bodylift
PW Dash
Towing Hookup
Bedliner
Heater Refresh
Calmini Rockers
Decal
DaveSport
Got Zuk Straps
Skid Plate
Heater Cleaning
Hood Swap
Wrangler Flares
Hood Latch
Mirror Install
NCO Rockers
Polyshield
Rag Joint
Rear Belts
IPF Head Lamps
Samurai Storage
SW Tank Skid
Petroworks Cage
Door Straps
TT Cage
Fender Flare
Tuffy® Console
Virtual Lift
ZDoor Strap
Wrenchin' with IZook
with Jim Bova

Yankee-Offroad Samurai Hood Latches

 

Have you ever had to open your hood in a hurry and had to search through a glove box full of junk? Or been in the nose up attitude and opened the glove box and had all that junk fall out onto your passenger? Well http://www.yankee-offroad.com has solved the problem with their new Samurai Hood Latches.

Select for larger image These are all the pieces included in the kit required for one side installation. The kit contains enough pieces for both sides
Select for larger image Lay a piece of masking tape to the rear of the side marker lamp up and over the fender. this will be used to mark the location of the holes for the bottom pieces.
Select for larger image Put a tape measure along the top of the fender from the rear of the fender where it meets the cowl forward. See picture.
Select for larger image This is the measurement from the cowl for the bottom bracket.
Select for larger image This is the measurement from the inside fender lip for the bottom bracket.
Select for larger image This shows the holes drilled. (Tip: Slot the holes slightly to allow a perfect fit)
Select for larger image Mount the lower bracket and secure the hold down with the pin, washer and cotter pin.
Select for larger image Use the plates supplied to mount the bottom and top brackets. (Tip: use a little silicon to prevent water getting under the brackets.)
Select for larger image This is a view of the completed hood latch. Looks great and very functional.
Select for larger image Another view of the completed latch.

Note: A cotter pin is supplied in the kit to allow you to drill the stock hood latch and pin it so it does not latch requiring the use of the inside handle release. I did not do this step seeing that I have no garage and often leave my Zook on the street and want to be able to lock the hood. I simply don't slam the hood when I don't want it to latch. Contact http://www.yankee-offroad with more info on the pinning.)

The Samurai Hood latches hold very securely. Installation is not difficult if you take you time and measure accurately. Also these are the measurements I used for where I wanted the Hood Latches to be on my hood. You can move the latches anywhere you desire on the hood. If you have any questions contact yankee-offroad or email me at redidbull@hotmail.com.

09/15/04 14:51

Looking for more exposure at your web site? We are  looking for contributing authors. Any article you provide will  be linked back to your site from the iZook web site with a full size banner at the top of your article.  This site  can only stay cutting edge with your input. E - mail me for details.  You can link to iZook with a new link button. Make sure to let us know if you use this button so a return link can be posted on the iZook links page.

Select this link for the Table Of Contents

Email Editor in Chief  Email Me!

iZook.com is Trademarked 1998-2007, iZook. All rights reserved.  This site is protected under copyright laws. Please do not use the iZook.com name or reprint any articles from this site without written permission. Copyright © 1998-2007, iZook. All rights reserved. 

Disclaimer: The fabrication, modifications and designs you see on this web site are completed by our readers and submitted to us for publishing.  If you duplicate these modifications you do so at your own risk. We do not endorse or make any claims to their safety, performance, On-road or off-road worthiness except as noted in our "Product Reviews". These reviews are on items purchased from or provided by reputable aftermarket suppliers.   Please see our legal information page for details. Suzuki, Samurai, Sidekick, Vitara, Grand Vitara, X-90, and the Suzuki "S" Logo are all registered trademarks of American Suzuki Motor Corporation. Geo, Chevy, and Tracker are all registered trademarks of General Motors Corporation. iZook is in no way endorsed by or affiliated with American Suzuki Motor Corporation.