CV Driveshaft

Tom Wood's CV Driveshaft

with Bill Johnston

	Next we attack the Spring Perches! If you were planning to do a SPring Over Axle conversion then this is the time to do it! The perches need to rotated so the pinion points to the transfer case. It is much easier to just weld on new perches and go. Otherwise you must remove the old components first without damaging the axle tubes. This vehicle had SPOA perches already, so they had to come off.
	The newly redesigned Rocky Road Outfitters SPOA Perches were used to replace the older perches. These are unique in design because the ends extend to meet the original perches down below. In the photos to the left it shows how much we had to rotate the perch to make up for the 12 degree difference we figured out in the beginning of the installation. We had to grind off a small amount from one "foot" to make the rotation possible. A couple of light tack welds were used to hold the perch in place while we applied the major portion of the heat to where the perches met. This ensures a solid weld without compromising the integrity of the axle tube. Then a little paint helps to keep the elements out of the nooks and crannies. Now put everything back together - and don't forget the brakes!
	Now it is time to install the adapter component that Tom includes with the drive shaft. Using the stock bolts, secure it to the transfer case flange. The bolt heads will be below the mating surface so they will not get in the way when you bolt in the CV joint. Tom includes the proper bolts to secure the CV joint end of the drive shaft to the adapter. Torque them to factory specs... these drive shafts can handle upwards of 1600 ft/lbs of torque, don't let loose bolts take away your new capabilities!
	The rear of the shaft will bolt up to the samurai pinion flange. I had a little trouble with the mating of these pieces because the pinion nut was coming into contact with the cast metal inside the yoke. A few passes with a file took down the offending metal on the nut and then it fit like a charm. I have talked to Tom about this and he is looking into the possibility that all pinion nuts aren't exactly the same throughout the model years. There should be no problem in the future. Torque everything to factory specs and you are ready to take on the world!
Quality components like these come with a hefty price tag. This unit sells for $425 (plus tax if you are a resident of Utah). But let's put this into perspective. I have two spare rear drive shafts (front shafts cut down for an extended length) in my garage that I have had to replace often because of trail breakage and vibration. Each of those 'junkyard specials' cost me about $120 each time I had to have one replaced or rebuilt. If I had gone with a drive shaft from Tom in the first place I know I would have saved some big bucks by now. For those of you that are thinking of making a purchase but want to save a few bucks, Tom will give volume discounts for clubs or small groups that want to place volume order. Tom will pick up the shipping charges to get you the drive shaft and components via UPS Ground. I was pleasantly suprised each and every time I talked to Tom during the course of this project. Not only does he make some of the most sought after drive shafts in the business, but he will take the time to talk with you about your application and any concerns you may have. He is also a fountain of knowledge, so don't hesitate to ask him the hard stuff!
Sources: CV Drive Shaft Tom Wood's Custom Drive Shafts 306 E. 31st Street Ogden, Utah 84401 www.4xshaft.com Toll Free in the U.S. 1-877-4XSHAFT (497-4238) 1-877-4XJOINT (495-6468) Worldwide 1-801-393- 4538 1-801-393- 4592	Click here to check out the extreme product review!
SPOA Axle Perches Rocky Road Outfitters P.O. Box 681245 Park City, UT 84068 www.rocky-road.com 1-888-801-7271 Orders 1-435-783-2990 Tech 1-435-783-4355 Fax

10/30/06 17:46

Looking for more exposure at your web site? We are looking for contributing authors. Any article you provide will be linked back to your site from the iZook web site with a full size banner at the top of your article. This site can only stay cutting edge with your input. E - mail me for details. You can link to iZook with a new link button. Make sure to let us know if you use this button so a return link can be posted on the iZook links page.

Select this link for the Table Of Contents

Email Editor in Chief

iZook.com is Trademarked 1998-2007, iZook. All rights reserved. This site is protected under copyright laws. Please do not use the iZook.com name or reprint any articles from this site without written permission. Copyright © 1998-2007, iZook. All rights reserved.

Disclaimer: The fabrication, modifications and designs you see on this web site are completed by our readers and submitted to us for publishing. If you duplicate these modifications you do so at your own risk. We do not endorse or make any claims to their safety, performance, On-road or off-road worthiness except as noted in our "Product Reviews". These reviews are on items purchased from or provided by reputable aftermarket suppliers. Please see our legal information page for details. Suzuki, Samurai, Sidekick, Vitara, Grand Vitara, X-90, and the Suzuki "S" Logo are all registered trademarks of American Suzuki Motor Corporation. Geo, Chevy, and Tracker are all registered trademarks of General Motors Corporation. iZook is in no way endorsed by or affiliated with American Suzuki Motor Corporation.